Archív –
iomega StorCenter ix2 - hálózati NAS hiányos, brickelt
5 000 Ft
| Állapot: | használt |
|---|---|
| Szándék: | kínál |
Archivált hirdetés
Eladó egy iomega StorCenter ix2 - hálózati NAS . 2 SATA hely van benne, RAID-ot is tud. Vinyók nélkül, hiányosan. Nincs meg külső burkolata, és a tápja se. Próbáltam életre kelteni, nem ment. Soros porton a hozzászólásban szereplőt adja 2 db 300-as vinyóval, imaga file-val. Hozzáértő kezekben szerintem életszhető. A neten van fent image file, amit 500-as vagy 1 terás vinyóra rakva elvielg indul.
Képek :
Hirdetés
Új hozzászólás
-
b-max
aktív tag
Ez a brickelt IX2 soros portos kimenete :
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DHNSMR03 LEU-Boot 1.1.1 (Jun 27 2008 - 13:41:46) USI u-boot-1.1.1-DHNSMR03/04-v128M
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[4096kB@ffc00000] [0kB@fa000000] ## Unknown FLASH at fa000000: Size = 0x00000000 = 0 MB
Flash: 4 MB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): DoneSoc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166MhzUSB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 66000000
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
## Booting image at ffc00000 ...
Image Name: Linux-2.6.22.7
Created: 2009-03-13 16:17:28 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1596848 Bytes = 1.5 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01200000 ...
Image Name:
Created: 2009-05-06 2:47:10 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 1201086 Bytes = 1.1 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OKStarting kernel ...
Uncompressing Linux........................................................................................................ done, booting the kernel.
Linux version 2.6.22.7 (soho@bsoho084.lss.emc.com) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #1 Fri Mar 13 12:17:24 EDT 2009
CPU: ARM926EJ-S [41069260] revision 0 (ARMv5TEJ), cr=a0053177
Machine: Feroceon
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists. Total pages: 32512
Kernel command line: console=ttyS0,115200
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 125240KB available (2996K code, 240K data, 116K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Sys Clk = 200000000, Tclk = 166666667CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....no such
DEVICE_CS1 ....base f4000000, size 32MB
DEVICE_CS2 ....no such
DEV_BOOCS ....base ff800000, size 8MB
CRYPT_ENG ....base f0000000, size 64KBMarvell Development Board (LSP Version 3.0.5_NAS_GDP)-- RD-88F5182-DAYTONA Soc: 88F5182 A2
Detected Tclk 166666667 and SysClk 200000000
Marvell USB EHCI Host controller #0: c0474600
Marvell USB EHCI Host controller #1: c0474400
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: orion_clocksource clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 1172K
RTC registered
cesadev_init(c001181c)
Use the XOR engines (acceleration) for enhancing the following functions:
o RAID 5 Xor calculation
o copy user to/from kernel buffers
Number of XOR engines to use: 2
NetWinder Floating Point Emulator V0.97 (double precision)
audit: initializing netlink socket (disabled)
audit(946684820.000:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
Marvell Ethernet Driver 'mv_ethernet':
o Uncached descriptors in DRAM
o DRAM SW cache-coherency
o TCP segmentation offload enabled
o Checksum offload enabled
o Rx desc: 128
o Tx desc: 256
o Loading network interface 'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access WDC WD3000JD-19KLB0 08.0 PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access WDC WD3000JS-00PDB0 21.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 586072368 512-byte hardware sectors (300069 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 586072368 512-byte hardware sectors (300069 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 1:0:0:0: [sdb] 586072368 512-byte hardware sectors (300069 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sdb: sdb1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
Iomega834x: Probing for flash...
Flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Iomega834x: Flash found at location 0xffc00000
Creating 3 MTD partitions on "Flash":
0x00000000-0x00200000 : "zImage"
0x00200000-0x00380000 : "initrd"
0x00380000-0x00400000 : "bootloader"
ehci_marvell ehci_marvell.4523: Marvell Orion EHCI
ehci_marvell ehci_marvell.4523: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.4523: irq 17, io base 0xf1050100
ehci_marvell ehci_marvell.4523: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_marvell ehci_marvell.167817: Marvell Orion EHCI
ehci_marvell ehci_marvell.167817: new USB bus registered, assigned bus number 2
ehci_marvell ehci_marvell.167817: irq 12, io base 0xf10a0100
ehci_marvell ehci_marvell.167817: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using ehci_marvell and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Sys UUID is :05e30ff0:b85227fd:f402ee2f:d068be91
Valid Disk 1 in md0: /dev/sda1
Valid Disk 2 in md0: /dev/sdb1
USB Device node is /dev/sdc1
Checking if there is an attached EMC Imager
scsi 2:0:0:0: Direct-Access HMS36040 4D5CF00 PQ: 0 ANSI: 0
sd 2:0:0:0: [sdc] 7999488 512-byte hardware sectors (4096 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sd 2:0:0:0: [sdc] 7999488 512-byte hardware sectors (4096 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
mount: mounting /dev/sdc1 on /usb_drive failed: Invalid argument
Checking for valid image in hard drives
md: md0 stopped.
md: bind<sdb1>
md: bind<sda1>
md: md0: raid array is not clean -- starting background reconstruction
raid1: raid set md0 active with 2 out of 2 mirrors
md: resync of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
md: using 128k window, over a total of 1020032 blocks.
md: resuming resync of md0 from checkpoint.
mdadm: /dev/md0 has been started with 2 drives.
No EMC Imager Found and No valid image in hard drive.
Going in to Network Imaging Mode
umount: cannot umount /usb_drive: Invalid argument
udhcpc (v1.8.2) started
Sending discover...
Sending discover...
Sending discover...
Sending discover...
md: md0: resync done.
RAID1 conf printout:
--- wd:2 rd:2
disk 0, wo:0, o:1, dev:sda1
disk 1, wo:0, o:1, dev:sdb1
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
No lease, failing
Network_imaging Stage 1
mknod: /dev/md0: File exists
md: md3 stopped.
mdadm: stopped /dev/md3
md: md0 stopped.
md: unbind<sda1>
md: export_rdev(sda1)
md: unbind<sdb1>
md: export_rdev(sdb1)
mdadm: stopped /dev/md0
md: md1 stopped.
mdadm: stopped /dev/md1
md: md2 stopped.
mdadm: stopped /dev/md2
10000+0 records in
10000+0 records out
Drive name = sda, Part size = 2040254
Valid partition found
10000+0 records in
10000+0 records out
Drive name = sdb, Part size = 2040254
Valid partition found
Creating raid 1...
md: bind<sda1>
md: bind<sdb1>
md: md0: raid array is not clean -- starting background reconstruction
raid1: raid set md0 active with 2 out of 2 mirrors
md: resync of RAID array md0
md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
md: using 128k window, over a total of 1020032 blocks.
mdadm: array /dev/md0 started.
Creating filesystem on /dev/md0...
mke2fs 1.40.2 (12-Jul-2007)
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
127744 inodes, 255008 blocks
12750 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=264241152
8 block groups
32768 blocks per group, 32768 fragments per group
15968 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376Writing inode tables: done
Writing superblocks and filesystem accounting information: doneThis filesystem will be automatically checked every 27 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
Device Model- m1
Device: Socket Listening on: 2081
Mac address = 00:d0:b8:0b:c2:28
Send: Network is unreachable
Mounting config image...
mount: mounting /sysroot/boot/images/config on /sysroot/boot/etc failed: No such file or directory
umount: cannot umount /sysroot/boot/etc: Invalid argument
Constructing root filesystem...
Bootstrapping ...
Initialization complete.
Freeing init memory: 116K
init started: BusyBox v1.8.2 (2008-12-19 23:42:04 EST)
starting pid 417, tty '': '/etc/init.d/rcS'
starting pid 421, tty '': 'umount'
BusyBox v1.8.2 (2008-12-19 23:42:04 EST) multi-call binaryUsage: umount [flags] FILESYSTEM|DIRECTORY
Unmount file systems
Options:
-r Try to remount devices as read-only if mount is busy
-l Lazy umount (detach filesystem)
-f Force umount (i.e., unreachable NFS server)
-D Do not free loop device (if a loop device has been used)The system is going down NOW!
Sending SIGTERM to all processes
Sending SIGKILLmd: md0 in immediate safe mode
to all processes
Requesting system poweroff
md: stopping all md devices.
md: md0: resync done.
md: checkpointing resync of md0.
md: md0 switched to read-only mode.
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronizing SCSI cache
Power down.
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 1:0:0:0: [sdb] Result: hostbyte=0x01 driverbyte=0x00Telefonos elérhetőség : huszas 92 6kettő 3O4 - Viber is
-
#26
Intruder2k5
MODERÁTOR
LevvaNN
#25
Intruder2k5
MODERÁTOR
Please use the private message feature, on the top menu of comments!
szép darab, jó cucc, a hangja is húzós 
Új hozzászólás
-
Fontos tudnod!
- Hogyan működik a Hardverapró?
- Soha ne utalj előre! Probléma, csalás esetén bármely hirdetésben ott a "Jelentem" gomb, használd!
- Mit tilos meghirdetni?
- Felhasználási feltételek (ÁSZF)
- Konkrét hibát itt, általános észrevételeket itt jelezz!
Hirdetés
-
AMD Radeon undervolt/overclock
lo Minden egy hideg, téli estén kezdődött, mikor rájöttem, hogy már kicsit kevés az RTX2060...
-
Júniusban Magyarországra érkezik a Tecno, a fejlődő piacok egyik kedvenc márkája
ma A Spark 20-as széria telefonjaival indítanak hazánkban, a negyvenezertől százezerig terjedő ársávban.
-
Megkérték az Apple beszállítóját, hogy ne használjon annyi áramot
it A Foxconn is azon cégek között van, amelyet megkértek Vietnámban, hogy jelentősen csökkentse az áramfogyasztását.
-
Sokkolóan drága az idei csúcs TCL tévé
ph A 114 hüvelykes képátlóval bíró 4K Mini LED QLED tévé árából egy egész korrekt autót lehet venni.
-
Ismét elhalasztották a Life by You korai kiadásának megjelenését
gp Jövő hónapban indult volna az early access, jelenleg azonban nem tudni hogy mikor debütál a játék.
Állásajánlatok
Cég: Ozeki Kft.
Város: Debrecen
Cég: Ozeki Kft.
Város: Debrecen