Eladó a képeken látható S21 Hydro Antminer.
A hűtőrendszer keringető szivattyúja sajnos megállt, a hővédelem pedig túl lassú volt.
2 db hasboard hibás. Jó a doboz, a tápegység, a vezérlő, a csatlakozók és 1 db hashboard.
Ha valakinek van szaktudása a javításhoz, BOS alatt 14 J/T-val megy névleges teljesítményen.
A gép jelenlegi indulási log állománya:
2025-11-17 14:33:40 power off
2025-11-17 14:33:41 miner ID : 8070ac2c1bdea81c
2025-11-17 14:33:41 FPGA Version = 0xB047
2025-11-17 14:33:41 ==========================capability start==========================
2025-11-17 14:33:41 board num = 3
2025-11-17 14:33:41 board id = 0, chain num = 1
2025-11-17 14:33:41 chain id = 0
2025-11-17 14:33:41 board id = 1, chain num = 1
2025-11-17 14:33:41 chain id = 1
2025-11-17 14:33:41 board id = 2, chain num = 1
2025-11-17 14:33:41 chain id = 2
2025-11-17 14:33:41 ==========================capability end============================
2025-11-17 14:33:41 chain num = 3
2025-11-17 14:33:41 skip loading levels for now
2025-11-17 14:33:48 load chain 0 eeprom data
2025-11-17 14:33:48 version invalid 5!=4
2025-11-17 14:33:48 version invalid 5!=4
2025-11-17 14:33:48 v5 load data succ
2025-11-17 14:33:48 v5 load data succ
2025-11-17 14:33:55 load chain 1 eeprom data
2025-11-17 14:33:55 version invalid 5!=4
2025-11-17 14:33:55 version invalid 5!=4
2025-11-17 14:33:55 v5 load data succ
2025-11-17 14:33:55 v5 load data succ
2025-11-17 14:34:02 load chain 2 eeprom data
2025-11-17 14:34:02 version invalid 5!=4
2025-11-17 14:34:02 version invalid 5!=4
2025-11-17 14:34:02 v5 load data succ
2025-11-17 14:34:02 v5 load data succ
2025-11-17 14:34:02 updated miner type to: Antminer S21 Hyd.
2025-11-17 14:34:02 load machine HHB68501 conf
2025-11-17 14:34:02 chain_num 3, chain_domain_num 18, chain_asic_num 216, domain_asic_num 12
2025-11-17 14:34:02 create thread get_nonce_and_register_thread
2025-11-17 14:34:02 fixed working voltage = 1960
2025-11-17 14:34:02 Chain [0] PCB Version: 0x0120
2025-11-17 14:34:02 Chain [0] BOM Version: 0x0000
2025-11-17 14:34:02 Chain [1] PCB Version: 0x0120
2025-11-17 14:34:02 Chain [1] BOM Version: 0x0000
2025-11-17 14:34:02 Chain [2] PCB Version: 0x0120
2025-11-17 14:34:02 Chain [2] BOM Version: 0x0000
2025-11-17 14:34:02 max sensor num = 4
2025-11-17 14:34:02 STATUS_INITED: soc init done!
2025-11-17 14:34:02 asic_temperature_and_voltage_monitor_thread start...
2025-11-17 14:34:02 temperature_monitor_thread start...
2025-11-17 14:34:04 start to init...
2025-11-17 14:34:17 get power version failed
2025-11-17 14:34:17 check power version failed, use v2 protocal to try it again
2025-11-17 14:34:19 power open power_version = 0x65
2025-11-17 14:34:23 power calibration data:
2025-11-17 14:34:23 5 B 92 41
2025-11-17 14:34:23 A1 A4 16 48
2025-11-17 14:34:23 45 7A 85 7E
2025-11-17 14:34:23 0 31 FD FC
2025-11-17 14:34:23 FD FC FD FD
2025-11-17 14:34:23 FC FF FC 80
2025-11-17 14:34:23 80 80 80 80
2025-11-17 14:34:23 1F E0 1B 41
2025-11-17 14:34:23 power is Calibrated
2025-11-17 14:34:23 power sn:KLKT331BDJCJA0326
2025-11-17 14:34:23 enable_power_calibration, calibration date:211208.
2025-11-17 14:34:23 start up min temp by 75a = 25
2025-11-17 14:34:23 Sensor localtion:3, Bring up temperature is 25
2025-11-17 14:34:23 reset low before power init
2025-11-17 14:34:28 get power version failed
2025-11-17 14:34:28 check power version failed, use v2 protocal to try it again
2025-11-17 14:34:30 power type version: 0x0065
2025-11-17 14:34:32 disable power watchdog: 0x0000
2025-11-17 14:34:33 Initializing the power, please wait, this may take up to 2 minutes...
2025-11-17 14:34:33 power off
2025-11-17 14:35:04 Slept 30 seconds, diff = 0.
2025-11-17 14:35:04 set_voltage_by_steps to 2130.
2025-11-17 14:35:14 water temp 25 ~ 26, stop.
2025-11-17 14:35:14 set UART baud to 115200
2025-11-17 14:35:22 Chain[0]: find 216 asic, times 0
2025-11-17 14:35:23 inlet_board_temp_max:35, inlet_board_temp_min:29, outlet_board_temp_max:31, outlet_board_temp_min:29
2025-11-17 14:35:23 water flow is reverse, please swap the water pipes at the inlet and outlet
2025-11-17 14:35:23 uninit_temp_info
2025-11-17 14:35:23 do not read temp anymore...
2025-11-17 14:35:23 uninit_asic_temp_vol_info
2025-11-17 14:35:23 do not read asic_temp_vol anymore...
2025-11-17 14:35:23 cancel thread
2025-11-17 14:35:23 ****power off hashboard****
2025-11-17 14:35:23 power off
2025-11-17 14:35:25 temp monitor thread exit
2025-11-17 14:35:29 Version num 256
2025-11-17 14:35:29 Mask num 0x1fe000
2025-11-17 14:35:29 Note: addrInterval or corenum is not initialized.
2025-11-17 14:35:29 Chain[1]: find 0 asic, times 0
2025-11-17 14:35:37 Chain[1]: find 0 asic, times 1
2025-11-17 14:35:45 Chain[1]: find 0 asic, times 2
2025-11-17 14:35:46 Chain 1 only find 0 asic, will power off hash board 1
2025-11-17 14:35:54 Chain[2]: find 0 asic, times 0
2025-11-17 14:36:02 Chain[2]: find 0 asic, times 1
2025-11-17 14:36:10 Chain[2]: find 0 asic, times 2
2025-11-17 14:36:11 Chain 2 only find 0 asic, will power off hash board 2
2025-11-17 14:36:11 stop_mining: (null)
2025-11-17 14:36:11 ****power off hashboard****